Request Quotation

XXODD Knowledge Bank

×

How to install the XXODD MonoAir

Installation Manual

Heating | Cooling | Plug & Play | DIY

The XXODD MonoAir is a full indoor monoblock air conditioner for heating, cooling, and dehumidification — with no outdoor unit and no installer required. This guide explains how to install, mount, and activate your MonoAir safely and correctly.

1. Before You Begin

Included Components

  • XXODD MonoAir unit
  • Wall mounting template
  • Mounting screws & plugs
  • Indoor & outdoor covers
  • Duct sleeves / pipes
  • Sealing strips
  • Fixing plate
  • Power cable (pre-attached)

Tools Required

  • Drill with hole saw (∅ 160
  • mm recommended)
  • Level
  • Pencil / Marker
  • Screwdriver
  • Measuring tape
  • Silicone sealant (optional)

2. Choose the Installation Location

The MonoAir must be installed on an exterior wall, as it expels heat outside through two ducts.

Installation Height

According to the spacing diagram on page 4 of the brochure, ensure:
  • 20 cm clearance above the unit
  • 10 cm clearance below
  • 10 cm clearance on both sides

Recommended locations

  • Living rooms
  • Bedrooms
  • Home offices
  • Apartments without
  • outdoor AC possibilities

Avoid:

  • Behind furniture
  • Behind curtains
  • Direct sunlight exposure
  • Close proximity to stoves,
  • radiators, or heat sources

3. Mark the Drill Holes

  1. Use the included wall template to mark:
    • The two duct positions
    • The mounting points
  2. Use a level to ensure the template is straight.
  3. Trace the holes clearly.

4. Drill the Wall Openings

  • Drill two circular holes through the exterior wall.
  • Keep a slight downward slope toward the outside to prevent condensation from entering the room.
  • Remove all dust and debris after drilling.

5. Install the Duct Sleeves

  1. Place the insulation / sealing strips around each duct sleeve.
  2. Slide each sleeve into the wall holes until fully seated.
  3. Apply sealant (optional) around the exterior side for airtightness.
  4. Attach the indoor and outdoor covers.

6. Install the Wall Bracket & Fixing Plate

  1. Drill and insert wall plugs where marked.
  2. Screw the mounting plate firmly to the wall.
  3. Ensure the mounting plate is level and fully secure.

7. Mounting the MonoAir

  1. Lift the MonoAir and align the unit’s rear ports with the installed ducts.
  2. Slide the unit onto the mounting plate until it clicks into place.
  3. Ensure:
    • The ducts are aligned
    • The unit is flush against the wall
    • No gaps or air leaks are visible

8. Electrical Connection

The XXODD MonoAir is a plug-and-play device.

  1. Plug the unit into a standard 220–240V outlet.
  2. Ensure the outlet:
    • Is grounded
    • Has no damage
    • Can support the rated power draw
The device powers on automatically once connected.

9. First-Time Setup

WiFi & App

The MonoAir works fully through WiFi (page 3 shows WiFi functionality).
  1. Download the XXODD App.
  2. Create your account.
  3. Add a new device → MonoAir.
  4. Connect to your WiFi network.
  5. Test:
    • Heating
    • Cooling
    • Silent Mode (39 dB)
    • Automation settings

10. Operating Modes

Cooling Mode

Efficient cooling for summer conditions.

 

Heating Mode

Heat pump + optional PTC boost up to 1000W (as shown in the spec sheet).

Silent Mode

Ultra-quiet at 39 dB for bedrooms or night use.

Dehumidification

Removes moisture up to 0.8 L/h.

Smart Climate Control

Automatically balances comfort and efficiency using indoor sensors.

Solar-Optimized Mode

Uses your own solar energy first when available.

11. Maintenance

Filters
  • Clean or replace every 3–6 months
  • Access by opening the front panel
Air Vents
  • Ensure indoor and outdoor vents remain unobstructed
General Cleaning
  • Use a soft cloth
  • Do not use chemical cleaners

12. Troubleshooting

No power
  • Check outlet
  • Check plug
  • Check circuit breaker
No cooling or heating
  • Ensure ducts are not blocked
  • Check airflow direction
  • Switch modes and restart
WiFi not connecting
  • Ensure 2.4 GHz network
  • Restart router
  • Re-add through the app

13. Technical Specifications (Summary)

(From the technical sheet on page 4)
  • Cooling Capacity:2,630 W
  • Heating Capacity:2,630 W
  • Rated Input:1000W / 730W
  • EER / COP:2.6 / 3.6
  • PTC Heater:1000W
  • Moisture Removal:0.8 L/h
  • Airflow:500 m³/h
  • Noise:39 dB (Silent) / 47 dB (High)
  • Room Size:32–40 m²
Product Size:1000 × 585 × 205 mm

14. Installation Complete

Your XXODD MonoAir is now ready to deliver efficient cooling, heating, and fresh air comfort — without an outdoor unit and without professional installation.

Related Articles

How to Install the XXODD Air Manager Pro
How to Install the XXODD Air Manager Light
How to install the XXODD QuickCharge
Is My Smart Meter Compatible With the XXODD P1 Meter?
How Does the P1 Meter Measure Gas Usage?
How Do I Install the XXODD P1 Meter?