How to Install the XXODD Air Manager Pro
Installation Manual
The XXODD Air Manager Pro is a high-performance wall-mounted heat-recovery ventilation system designed for continuous fresh air, efficient heat exchange, and superior indoor comfort.
This guide walks you through the full installation process.
1. Before You Begin
Included Components
- Air Manager Pro unit
- Wall mounting bracket
- Dual duct pipes
- EVA insulation sleeves
- Fixing screws & anchors
- Front panel
- Remote control (depending on model)
Tools Required
- Hole saw or core drill (∅ 80–100 mm per duct)
- Power drill
- Screwdriver
- Level
- Marker
- Tape measure
- Protective sheet for dust control
2. Choosing the Installation Location
Place the unit on an exterior wall, at a height that allows comfortable servicing.
Avoid installing near:
- Direct heat sources
- Gas appliances
- Curtains or blocked airflow zones
Leave enough space on both sides for maintenance and duct routing.
3. Marking the Wall
- Position the unit against the wall to determine the mounting height.
- Use a level to ensure perfect alignment.
- Mark the outline of the two duct openings.
- Mark the screw positions for the mounting bracket.
(Based on the wall-marking steps shown in the installation sheet.)
4. Preparing the Duct Openings
- Cover the floor with a protective sheet to catch drilling dust.
- Drill two circular holes straight through the exterior wall.
- The holes must be clean, smooth, and aligned with the markings.
- Ensure the holes angle slightly downward toward the outside to prevent moisture ingress.
5. Installing the Duct Pipes
- Wrap each duct pipe in the provided EVA insulation sleeve.
- Insert the ducts into the wall openings from the inside.
- Ensure the ducts extend fully to the exterior side.
- Fix the ducts in place so they are tight, stable, and sealed.
6. Mounting the Wall Bracket
- Drill the screw holes using the markings you made earlier.
- Insert wall anchors if required.
- Place the mounting bracket against the wall.
- Fasten it securely with screws.
- Re-check alignment with a level.
7. Installing the Air Manager Pro Unit
The front panel is magnetic for easy access.
- Lift the Air Manager Pro and hang it on the mounting bracket.
- Ensure the duct pipes align with the inlets on the rear of the unit.
- Push the unit gently until it sits flush against the wall.
- Tighten the fixing screws to secure the device.
8. Internal Setup
- Open the front service panel.
- Remove any protective packaging materials.
- Pull out and remove the plastic safety bag inside the unit.
- Insert or check the filters and heat-exchange core.
- Close the panel securely.
The device powers on automatically once connected.
9. Electrical Connection
- Connect the power cable to the designated input.
- Ensure the socket is easily accessible.
- Secure the cable to prevent strain or accidental removal.
The Air Manager Pro is designed to operate on household voltage and requires no external transformer.
10. Final Assembly & Testing
- Attach the top cover and front panel.
- Switch power on.
- Test airflow in:
- Fresh Air mode
- Exhaust mode
- Heat Recovery mode
- Use the remote or app (WiFi models) to verify speed control and mode switching.
- Ensure airflow is balanced and noise levels are normal.
11. App Control (WiFi Models)
The Air Manager Pro can connect to your home WiFi and be controlled through the XXODD App.
Features include:
- Fan speed control
- Fresh-air schedule
- Humidity automation
- Remote control outside the home
- Multi-unit synchronisation
12. Routine Maintenance
Filters
- Clean or replace filters every 3–6 months
- Remove the front panel to access them
Heat Exchange Core
- Check and clean gently once per year
Exterior Vents
- Ensure outdoor vents remain free of dust, insects, and debris
13. Safety Notes
- Always disconnect power before internal cleaning
- Do not block inlet or outlet vents
- Do not install near flammable substances
- Ensure all duct sealing is airtight
- Only use XXODD-approved replacement parts
- 1. Before You Begin
- 2. Choosing the Installation Location
- 3. Marking the Wall
- 4. Preparing the Duct Openings
- 5. Installing the Duct Pipes
- 6. Mounting the Wall Bracket
- 7. Installing the Air Manager Pro Unit
- 8. Internal Setup
- 9. Electrical Connection
- 10. Final Assembly & Testing
- 11. App Control (WiFi Models)
- 12. Routine Maintenance
- 13. Safety Notes